Kill Mold Inside Walls
Killing Mold Inside Of Walls

WILL OZONE TRAVEL INTO WALLS AND KILL MOLD INSIDE A WALL?

No.  Ozone, or anything else, is NOT going to travel inside a wall to kill the mold in a wall.
It is NOT physically possible to kill mold inside a wall without removing the wallboard.

If mold is living inside the walls the ONLY way to kill the mold is to take down the wallboard, discard the mold infected wallboard, and then blast the inside of the walls with High Ozone Shock Treatments to make sure that it is all dead.

The way that you kill mold inside a wall is to REMOVE THE WALLBOARD and blast behind it with very high ozone shock treatments.  The wallboard MUST BE REMOVED and the open area must be blasted with ozone, preferably many times. 
Mold infested wallboard MUST be thrown away because it is a porous material that mold cannot be killed inside of.

Just cleaning the area out behind the wall with bleach or fungicides is not enough to make sure all of the mold is killed.

You MUST make sure the mold is 100% dead or when you rebuild your walls  or the spores may start to reproduce within the wall cavity and a few months later.  Soon you could have the exact same mold problem  that you started with.  We hear about this exact situation almost every day.  Not killing ALL the mold inside a wall will only result in you having to do the exact same job all over again. 

Some companies are now saying that they have "specially created" form of ozone or that they use "negative pressure" that will get the ozone inside of walls to kill the mold and bacteria inside them. 
This is simply not true.  Others say you can cut holes in the wall and "inject" ozone into the wall cavity to kill mold. 
Again, this is not true.

Many ozone companies have been sued by the government by making false claims such as that ozone will pass through walls.  But that is 100% NOT true, and anyone with common sense will recognize that.

Once again this is not going to work.   Let's think about this logically:
Every wall has a stud 16 inches apart that the wall board is nailed right up against.  They also have crossbeams halfway up the wall.  That means behind even a short 4 or 5 foot wall there are at least 8 separate cavities. 

So simply injecting the ozone into one cavity is only going to affect a very small cavity, not the entire opening behind a wall.   Even if "negative pressure" is used it will never be strong enough to draw the ozone through all the separate wall cavities.   It is simply not possible because the wallboard is nailed right up against the studs and there is no, or very little air leakage between them.

It does not make sense to cut 8, 12, or 20 holes in your walls to inject the ozone inside them.
Besides, the wallboard itself is most likely infected with the mold inside it's core so it is going to have to be replaced anyway.

The solution is to remove the entire wall, clean out any mold and mold infested insulation and nail up new wallboard.  Of course it is strongly recommended that ozone be used in this mold remediation process.

Some people ask us if they are going to open up the walls and rebuild anyway why bother using ozone at all? 
The answer to that is very simple.  One must make 100% sure that all the mold is killed behind a wall before they ever rebuild, or they leave the very real possibility that the mold will start growing behind the walls in just a short time once again.

One of the most common stories we hear almost every day is that someone has torn down their walls, did a quick mold cleanup, and then 6 months later the mold is growing once again.

We recommend that when walls are opened up that the entire room be blasted with very high levels of ozone, many times over a period of days, to make absolutely sure all the mold has been killed.

It is still wise to blast rooms that may even have mold behind the walls because it can kill the mold that is on the surface of the walls, and in the air, and therefore make it much safer to be in that room.

Even if you can't open up the walls and repair them right away, at least blasting ozone into the room will minimize the severe health consequences that can occur from even a slight mold exposure.

Ignoring a mold problem is not going to make it going to go away, and it will only continue to get worse over time. 
All the while the mold can be negatively affecting your health in an irreversible manner
It is imperative that rooms with mold in them be blasted with High Ozone Shock Treatments as soon as possible to kill any mold that is living in them.

Ozone, or anything else is NOT going to travel inside of walls no matter what anyone else may tell you. 
It is simply not possible.  We wish that it would so that it would make the job of mold remediation much easier, but no gas, oxygen or ozone, can pass through your walls.
 

Professional High Powered Ozone Generators  XT-2000  XT-4000 XT-6000

Heavy Duty Professional Grade Ozone Generators Air-Zone XT-14000 Professional High Powered Ozone Generator U.S. Patented Ozone Elements Produces Zero Nitrogen Oxides 21st Century High Tech Design BUILT IN TIMER Features very high ozone outputs of 4500, 9000, or 14000 mg/hr Extra Thick Rust & Oxidation Proof  Stainless Steel Case & Chassis CLICK HERE to learn more about the amazing XT-14000!

Air-Zone XT-28000 Professional High Powered Ozone Generator U.S. Patented Ozone Elements Produces Zero Nitrogen Oxides 21st Century High-Tech Design BUILT IN TIMER Features astounding ozone outputs of 28000 mg/hr! Extra Thick Rust & Oxidation Proof  Stainless Steel Case & Chassis CLICK HERE to learn more about the amazing XT-28000!

Ozone helps destroy, not just cover up these kinds of odors

Mold Test Kits Mold test kits are the method professionals use to determine if there is a mold problem.  Our simple, do-it-yourself test identifies dangerous molds & mildew in 48 hours.  Optional lab analysis is available to indicate the exact count and type of mold & mildew present. The kits may be used one time. For multiple area testing additional kits will be required. Mold testing is the only way to know what kind of mold you have. Testing is also the only method to know if you have killed the mold after remediation. Click Here to learn more about our professional Mold Test Kits.

MOLD TEST KIT $19.99 Each

BUY TWO AND SAVE $34.99 for TWO

BUY FIVE AT A DISCOUNT $69.99 for FIVE

Ultraviolet Mold Inspection Lamps   Ultraviolet inspection lamps can identify the location of mold, bacteria, urine, and many other contaminants.  Identifying the location of the contaminant can greatly aid in it's remediation by ozone. Many times there is an odor in a room, but it may not be clear where it is coming from. These lamps can help determine the location of an odor and make the remediation job easier. These professional lamps are designed to display ultraviolet light in long wave frequencies. Long wave UV light is required to find contaminants such as urine and mold.  CLICK HERE to read more about our Ultraviolet Mold Inspection Lamps

Ozone helps destroy, not just cover up these kinds of odors

Household Odors	Indoor Air Pollution	Fire & Flood Restorations
Mold & Mildew	Hotel / Motel Rooms	New Carpeting Fumes
Smoking Lounges	Pet Odors	Bars
Restaurants	Boat Bilge Odors	Greenhouses
Chemical Fumes	Garbage Areas	Auto Restorations
Vermin & Pest Control	Furniture Restorations	Clothing Restorations


 

In today's times when everyone is concerned with  infectious bacteria, it is a good idea to sanitize rooms with High Ozone Shock Treatments. Killing germs, bacteria, and viruses with ozone may be one of the best ways to protect your family  from the complex diseases we face today. CLICK HERE to read how ozone helps kill bacteria.