We also use high temperature, shatter resistant, tempered glass in our innovative ozone elements.

A U.S. Patent takes years of research and engineering design submissions to obtain. 
Over 95% of patent applications are rejected.
It is extremely difficult to receive a U.S. patent as the inventor must prove it is a different and new design.
It took our engineers over 10 years to design these new ozone elements, and what they have invented is state of the art. 
Our engineers designs are light years ahead of any other ozone technology available today.

Almost every other high powered ozone generator produced today uses basically the same system;
A transformer that supplies a high voltage to two screens separated by a piece of non-conductive material such as glass or mica. Some use screens, some use rods or tubes.
Basically it is the same system in different forms. These systems can produce high amounts of ozone, but they have some inherent problems. 

First:
These same plate designs have been used for over 100 years!
Thomas Edison used this exact method to produce ozone in 1900, before they even had instruments to measure ozone!

Second:
The ozone plates or screens must be perfectly aligned to produce the maximum amount of ozone they are designed for. If the grids are not aligned properly ozone production drastically drops. If the grids are too close to each other the high voltage will arc from one grid to another. Ozone production gets lower and lower, and eventually the transformer blows out from overload.
The plates often have to be completely removed and fully cleaned. Then they have to be reassembled by the users in a perfect manner for them to work properly.

Third;
These old fashioned screens, or plates must constantly be cleaned to work at maximum efficiency. If allowed to remain dirty the plates arc across the buildup of gunk and the transformer again blows out. Our patented ozone elements are designed to resist dirt buildup and not have these problems.

We think it too much to ask that every one of our customers become an ozone engineer, and have to deal with all these problems.

All you have to do with our patented ozone elements is replace the inexpensive air intake filter on the outside of the unit from time to time. 

The elements may also be blown out with air to remove any visible dust. We think this is a lot easier than removing, cleaning, and perfectly reassembling all the components of each plate.

Our patented ozone elements are in a completely sealed housing so that there is absolutely no adjustments required.
There are no other corona elements like them available anywhere. Our patented ozone elements are in a sealed non-adjustable housing so that their alignment is always perfect. 
This is a far supierior element design than ANY other ozone generator manufacturer has.

Due to their design they resist accumulating dirt. When they do burn out, and ALL ozone producing elements eventually will, they are extremely cheap and easy to replace. 
If an element burns out it can be replaced by almost anyone with a screwdriver in about 5 minutes. You simply remove the front cover, slide the old element out and disconnect the wires. You then connect the wires to the new element, slide it back into it's slot, and screw the cover back on. No alignment, no assembly, no hassle. They are also very economical to replace costing about $5.00 per year of use.

There are no adjustments, zero nitrogen oxides, nor is their any major cleaning required of them. As long as the air intake filter is replaced occasionally these elements will last for years. The air filters cost only pennies.
Any unit without a dust filter will get dirty, and is destined to fail.

This is 21st century design when every other ozone company is still using 19th century designs!!
Our replacement elements are also extremely low priced, and they only cost pennies per each month of use.

Some companies berate our patented ozone elements for being disposable. They are disposable and they are designed that way so the customer can replace these inexpensive ozone elements in minutes.
Our patented ozone elements also last as long or longer than any other ozone elements produced anywhere.

Old fashioned ozone plates with their 100 year old design are now considered archaic. Manufacturers continue to use them because they are extremely cheap to produce, or they have no idea of how to make a better plate. Other companies don't even understand how our ozone elements work!

Air-Zone® U.S. Patented ozone elements

cheap Mica ozone plates

Air-Zone offers the highest ozone output per dollar of any ozone generator brand. The only way to compare ozone generators is by the output in milligrams per hour (mg.hr.).  No other company offers as much ozone as we do for as low a price as we do.  Combined with our features of Patented Ozone Elements, and the convenience of remote control, there is simply no better ozone generator value available today.

True Ozone Outputs

All Air-Zone® ozone generators have had their ozone outputs independently measured by SGS, the worlds leading verification, testing, and certification company. The world  respected Société Générale de Surveillance otherwise known as SGS. SGS provides true certifications that cannot, on their companies well respected reputation, be called into question.

Many other ozone companies simply test their own machines under questionable conditions and their mg/hr output levels of ozone might not be quite accurate. 

You may run across a company that tells you they have measured our machines and our ozone outputs did not measure up to what we state they are.  That's why we use the independant tests from SGS that cannot be called into question.  Be sure an ask them which independant organization has tested their machines.

Ion Generators simply negatively charge the air's ions so that floating dust particles will cling to a surface in the room, much in the way static electricity does. They are toys compared to real ozone generators.

There are quite a few problems associated with ion generators. To do air cleaning, meaning removing pollutants, you need a very large amount of ions. More than has been recognized as a safe level.  According to air science,  indoor air has 100 to 200 ions per cubic cm, outdoor fresh air has 200 to 500 ions per cubic cm,  and a fresh clean forest will have 1,500 to 5,000 ions per cubic cm.

Ion generators typically produce more than 1,000,000 to 10,000,000 negative ions per cubic cm. Some machines even boast an output of 500 trillion negative ions per cubic cm! This is simply too much. 

Air-Zone's ozone generators produce negative ions of about 10,000 to 30,000 per cubic cm. Therefore, the amount of negative ions output from our ozone generators is good enough for giving indoor air that fresh clean smell, and yet is not too much as to be irritating to your eyes, lungs, and throat.

Overuse of negative ionization pushes dust particles to the walls and floor. In fact for ionization to be truly effective, ionizers must generate so many ions that they cause headaches and sore throats.

The fact is even with this overabundance of ionization there is only limited, temporary air cleaning being done and ZERO Air Purifying being accomplished. Nothing is being killed by the ions. Nothing is being Purified.

The problem with this is that the same dust can be kicked right back into the air for you to breathe. The dirt that does not begin to float again will stick to whatever surface is close. After a few months walls, floors, appliances, and furniture begin to build up a layer of dirt on them. If you put an ionizer on a table near a wall, the wall will develop a black halo of dirt in just a couple of days!

Realize that what all so-called "air cleaning" ionizers do is limited to pushing around lightweight particles of dust. They cannot effectively kill odors.

For removing odors, and light dust only OZONE works the best by killing the offending organisms.

If in fact you have severe dust problems it is much better to collect dust in a true HEPA filter rather than have an ionizer create a film of dirt on your household surfaces. We also offer a high quality line of the worlds best HEPA filters for serious dust & dander problems.

Nitrogen Oxides are a by product of every other corona discharge ozone generation system available today. These gases are undesired and have even been found to be dangerous to living beings. Some ozone generation systems put out an extremely high amount of these gases. 

Old fashioned corona ozone plates can produce high amounts of Nitrogen Oxides. These oxides are irritating to breathe, and could be dangerous. Nitrogen Oxides have no desired place in ozone production.

Just about every ozone generator manufacturer simply uses open cased, iron core, high voltage transformers. 
Unless a very expensive oversized transformer is used  the transformer can burn out by the shorting out of the old fashioned ozone generator plates. 

Companies don't want to spend the money for expensive oversized transformers and thus they often fail. 
One company even uses the same transformer in their $200 model as their $1100 model.   To us that spells rip-off. 
It also leads to premature failure of the power transformer.

Standard transformers are coils wound on an exposed iron core. This core is extremely susceptible to rust and oxidation. 
The transformer literally self destructs in a high moisture, high ozone environment. 

As the core and windings degrade it eventually shorts out and blows.  Considering these are units in high ozone generating machines, and the fact that ozone generators are often used in moist environments to combat mold and mildew, it is simply not a very smart idea to use these types of transformers in an ozone generator since they are destined to eventually fail.
Transformer burnout accounts for a large amount  of ozone generator failures. 

It was recommended to us to use completely enclosed transformers.  Not only are the core and windings protected from moisture and oxidation, these transformers are also very stable and burnout resistant.  These units are more expensive, but in the long run it eliminates the time and effort of replacing the transformer, the most expensive component in any ozone generator.

Air-Zone® only uses completely sealed transformers that are properly heat sinked for even heat dispersion. 
We use oversized transformers so that they rarely even become warm to the touch.

Our larger models include additional transformers in order to be able to handle higher ozone outputs.
Our largest models contain 12 transformers.
Some companies who try to get away by simply using just a single transformer in all their models.  They may even use the exact same transformer in every model!
How can a single transformer handle the loads of a machine that vary in ozone levels 30 times from their smallest model to their largest? It's just not sound engineering.

Air-Zone® uses multiple transformers in our different models.  How can a single transformer that is used in a small ozone machine be expected to handle the much higher load in a large ozone generator?

Many competitors machines simply use ONE transformer, the SAME EXACT transformer in many of their different low and high ozone output generator models.

Whether it be a single plate 1000 mg/hr model, a 5 plate 3600 mg/hr model, a 5 plate 5000 mg/hr model, or a 10 plate 10000 mg/hr model, some manufacturers use the same exact transformer in every machine.

How can the SAME transformer that is expected to handle one high voltage ozone element, handle ten high voltage ozone elements?

If a competitor states "Our transformer is so good we can use the same one in our low powered model as our high powered model" then what justifies the huge jump in price between the low and high powered models?
It seems to us they are just charging the customers empty dollars of more and more profits for increased ozone power.

That leads us to two possible conclusions: Either the transformer in the 10 plate 10,000 mg/hr model is woefully undersized, or 1000 mg/hr ozone generator is using a transformer that is already properly sized for a higher powered machine,

If the latter is the case, and the ozone plates are as low cost as they say, then why the huge price jump between lower and higher powered ozone generators?

That's why ozone generators that are "upgradable" by simply adding more ozone plates are not very well designed.
The load on the transformer HAS to be radically different on a single or five plate ozone generator. 

This is proven by the fact that when a competitor adds 4 more ozone plates to a 1000 mg/hr machine that the total ozone output does NOT equal 5000 mg/hr. 

The "upgraded" generator now only puts out 3600 mg/hr, the missing 1400 mg/hr of ozone output has been lost because the transformer has a hard time handling the different load. That is the indication of a poorly designed ozone generator.

That proves that the load is radically different when you simply add more ozone plates to a power transformer. 
If the transformer has been strained so that it looses that much ozone power, then it can be concluded it is that much closer to straining and blowing out.  It has to run at a higher temperature. 

Upgradable ozone generators can very unstable due to the additional load placed on the transformer
They are the "cheap" way to solve a complicated problem instead of making a properly designed machine.

Our XT-2000 uses a single transformer. The XT-4000 uses 2 transformers. The XT-6000 uses 3 power transformers. 
Our XT-14000 uses 6 power transformers and our XT-28000 uses 12 separate transformers.

We do this because to present a balanced load, and to have even power distribution. 
It is better to use multiple transformers when doubling or tripling the ozone power.
It only makes good sense. It makes for a more balanced ozone machine.

We don't just add two more ozone elements to the XT-2000 to make it a 4000 mg/hr machine.
The XT-4000 uses 2 separate transformers. Simply adding ozone elements isn't the proper solution.  Adding 2 more elements would NOT equal 4000 mg/hr. It might only increase the ozone power to 3200 mg/hr because the load presented to the transformer would be completely different.

That's why ozone generators that are "upgradable" by simply adding more ozone plates are not very well designed. 
The load on the transformer MUST to be radically different on a single or five plate ozone generator.

Keep in mind the fact that competitors also use ozone plate technology where each "plate" has 3 pieces in it that can easily move around.  They use a spring system to keep each part of the plate in perfect alignment.   A 10 plate, 10,000 mg/hr ozone machine will have 30 separate pieces in its 10 ozone plates! 
A 10,000 mg/hr "plate type" ozone machine has 30 separate parts that must ALWAYS be in perfect alignment or the parts will short out and the transformer will burn out.

If a single piece of the glass or mica non-conductor breaks, cracks, or just slips out of alignment due to a lack of spring tension, then the electrical conductor, screen parts of the ozone elements can arc and cause an electrical short.  With 30 separate parts in this type of configuration the likelihood of a problem like this happening is very high.

When an ozone plate short outs, the transformer is also shorted out.  No matter how well it is built, a transformer cannot stand being shorted out for very long.   The transformer will get very hot, very quickly.  Electrical transformers cannot stand to have a high voltage, shorted load on them for very long without blowing out.
We know this because we have tried that type of technology and found it to be very unstable.

Air-Zone® not only uses multiple transformers in our higher powered units to help balance the load, we also use our U.S. patented ozone elements which do not have components in them that can move, or shift out of alignment. 
There is no possible way for them to short out as standard ozone plates can.

Don't buy the argument that using multiple transformers gives a machine more to break down. 
The truth is if properly sized transformers are used, and not strained by overloading them with too many ozone plates, there is very little chance they will blow out.
Simply adding ozone plates as some other manufacturers do, is what overloads electrical transformers and makes them more likely to blow out.

Our XT-14000 and our XT-28000 use special monitoring circuits, and indicator lamps on the front panel to always let the user know the status of each ozone element and transformer.   No other ozone generator made has this feature.
If a transformer ever blows out the user will know about it right away.   Because of these units modular construction this problem is very easy to fix.

Air-Zone® ozone generators are simply more stable ozone generators than most other brands.
Electronic protection circuits and fuses prevent our internal components from overload & burnout.

Air-Zone® uses High Impact Top Grade PVC outer cases and inner chassis. Why PVC plastic and not steel or aluminum? The reason is cheap steel will rust and oxidize in a high ozone environment. 

Many companies are even using pretty wood boxes that resemble loudspeakers. These ozone generators look nice but it is highly impractical to use wood as an ozone generator housing. It will quickly deteriorate and warp in a high ozone or moisture filled environment. Wood cabinets look nice, but are highly impractical for use in an ozone generator.  They can actually begin flaking apart in just a few months of use.

We came to the conclusion that using High Impact PVC Plastic for the outer casing and the inner chassis was the way to go. PVC does not oxidize nor deteriorate with age and use in a high ozone, or moist environment.
After much testing we found that PVC plastic was the way to go. High Impact PVC's are also used in the construction the United States Space Shuttles.
High Impact PVC is extremely sturdy, and expensive. Don't be fooled by other companies who use cheap grades of plastic that are easily breakable. High Impact PVC will last for years, it is tough, and it can take a beating.

Many ozone generators made today actually self-deteriorate in a high ozone environment. They actually end up destroying themselves.  Our ozone generators are built from the best materials we can find. No expense has been spared in making them the best ozone machines available. 

The XT-28000 is built using a very high grade of  surgical steel that resists oxidation in a high ozone environment.  Most ozone generators made out of steel use a cheap, thin, steel that rusts in a short time.

Ozone Element & Fan Placement

When ozone elements are located deep inside the machine the ozone buildup inside the unit actually begins to self destruct in the high ozone environment. All our ozone elements are in front of our machines so that the ozone has no chance of destroying the ozone generator itself.
Many companies place the fan in front of the ozone elements.  Ozone is a very powerful oxidant. Placing the fan in front of the ozone elements allows the ozone to eat away the fan causing early failure. 
Air-Zone's fans are placed behind the ozone elements to push the ozone out of the machine.

Electronic Control Circuits

Believe it or not many ozone generators internal wire connections are simply pieces of bare wire twisted together and held in place by a simple wire nut. In a unit designed to be moved to different locations, vibrations can eventually loosen the wire connections. The copper wires are stranded and every strand will oxidize and eventually you have a bad connection point. 
In a high ozone environment the oxidation of exposed wires can occur very quickly.

This method of wire connection is outdated in a product such as on ozone generator and can only lead to disaster.
ALL internal connections of our ozone generators are soldered into place. Even if the outside of the soldered connection oxidizes 95% of the connection will always remain intact because the connections are held together by melted metal.
Soldering is the only sensible way to connect wires in the 21'st Century.

Air-Zone®  uses True Wireless Remote Controls on our ozone generators designed for home use. All of the units functions including on/off, ozone output levels, fan speeds, and timers can be controlled from across the room with our sophisticated hand held remotes. No other manufacturer uses true remote controls like we do.

Warranty

Our units are fully warranted for 5 year parts and service.
Please click here to read our complete warranty.

Air-Zone® manufacturers, sells, and services all our own products directly.  We are not a multilevel marketting company and we do not have an outside dealer network.

When you buy a product from a multilevel marketer or even a drop ship dealer of a product they certainly aren't going to fix your product, they are simply going to blindly send you back to their manufacturer who doesn't even know who you are!

Air-Zone® handles all our own product services.  We feel if you buy from us then we should be responsible for taking care of your warranty service.  When you call us for warranty we know who you are, we have all your transaction data on file.

When you buy a product from another company who is just a dealer of those products you have to prove who you are to the "other" company who will be repairing your product. You didn't buy your product direct from that company , as you would have done from us, so that "other" company fixing your product doesn't even know who you are.

Anyone who has bought some of our competitors machines, and tried to get service for them, knows that can be a painful experience all to well.

That won't happen with Air-Zone® because we sell and service all our own ozone products.

If you have any doubt as to the validity of another companies warranty, or to compare it to ours please contact us and we will compare warranties for you.

Air-Zone® is a member of the Better Business Bureau and we abide by it's advertising guidelines.

When you buy from Air-Zone® you are buying direct from the source. We are not a multilevel marketing company. We engineer and design all our own products. All our products have United States patents.

Our senior engineer has over 25 years experience working with ozone, and is the leading pioneer in the industry.

Not satisfied with inferior 1890's "slap a cheap high voltage transformer to a couple of screens and a glass or mica plate", our engineers have worked for years to develop new methods of creating ozone by refining existing technologies. 

Our senior engineer holds 10 international patents ( 6 U.S. ) for creating a new type of corona discharge element that is unlike any other. His element design is a self contained modular unit, that produces large amounts of ozone, with zero amounts of Nitrogen Oxides.